Supported Beams
W beam
| Section |
min. |
W6x9 |
max. |
W21x166 |
|
|
| Length |
min. |
10 ft |
max. |
45 ft |
|
|
HSS closed rectangular column
| Section |
min. |
3x3x0.100 |
max. |
20x12x5/8" |
|
|
| Length |
min. |
10 ft |
max. |
45 ft |
|
|
Channel Beam or U-Beam
| Section |
min. |
C6x8.2 |
max. |
C15x50 |
|
|
| Length |
min. |
10 ft |
max. |
45 ft |
|
|
Supported Accessories
Angles
| Section |
min. |
1.5" x 1.5" x 3/16" |
max. |
8"x8"x1" |
|
|
| Length |
min. |
2" |
max. |
36" |
|
|
Plates (rectangular shape)
| Section |
smallest |
2"x2"x1/8" |
thickest |
22"x22"x1.5" |
largest |
36"x36"x0.5" |
Other characteristics:
| Supports rusty parts |
|
Yes |
|
|
|
|
| Weight supported maximum |
|
300 lbs. |
|
|
|
|
Inspection
| Beam torsion and flexion compensation |
|
Yes |
|
|
|
|
| Hole position inspection |
|
Yes |
|
|
|
|
| Welding quality inspection (or identification) |
|
Optional |
|
|
|
|
Second inspection to check if complete
assembly was welded according to CIS/2 |
|
Optional |
|
|
|
|
Logging of every weld and inspection
done on each beam assembly, with date
and hour, face and result. |
|
Yes |
|
|
|
|
Welding
Reading welding information from
CIS/2 file |
|
Yes, but not required |
|
Generating welding information from
components |
|
Yes, for supported accessories
and supported welding type only. |
|
| Part gap management during welding |
|
Yes |
|
Types of welding supported:
| Process and position |
|
MCAW – Flat and Horizontal |
|
| Transfer mode |
|
MCAW – Short-circuit, globular,spray |
|
| Classification of wire |
|
MCAW – ER70S-6 |
|
| Diameter of wire |
|
MCAW – 0.045" |
|
| Protection gas |
|
Ar-CO2 mix |
|
| Torch angle |
|
MCAW – Straight and push 10° |
|
| Standards |
|
CSA W59 |
|
Trajectory Continuity:
| Continuous |
|
Yes |
|
| Segmented |
|
Yes. |
|
Number of pass:
| Single-pass |
|
Yes |
|
| Multi-pass |
|
No |
|
|
|
|
|
| Welding types supported: |
|
Fillet, Lap |
|
Preparation type:
| No preparation |
|
Yes |
|
|
|
|
| Pre-heat |
|
No |
|
|
|
|
| Gouging |
|
No |
|
|
|
|
| Maximum length: (inches) |
|
24 |
|
|
|
|
| Turning corners while welding |
|
Yes |
|
|
|
|
Welding between:
| Beam and other accessories |
|
Yes |
|
|
|
|
| Accessories and other accessories |
|
No |
|
|
|
|
|
